Building A Deck On A Membrane Roof / 17 Best images about Construction Details on Pinterest | Wall mount, Green roofs and Decks : A properly constructed epdm roof should last 40 or more years.

Building A Deck On A Membrane Roof / 17 Best images about Construction Details on Pinterest | Wall mount, Green roofs and Decks : A properly constructed epdm roof should last 40 or more years.. Here are the details in case you'd like to build your own building a deck with a roof version. Epdm is a rubber like sheet used for waterproofing surfaces. 5 roof expansion joints (see construction details to view the illustrated application of roofstar guarantee standards for various membrane assemblies).

A membrane roof should always provide positive drainage — the roof may look flat, but it shouldn't be level. My biggest question is with the rubber membrane, piercing it (yikes!), and properly anchoring the deck to the building. Several commercial waterproof deck systems are available to create a dry space under a deck, but rune'stactic of adding a roof to a deck seems to be just as effective. Here are the details in case you'd like to build your own building a deck with a roof version. The downspouts can be oriented to fit between joists spaced 12 or 16 inches on center.

Installing Site-Built Under-Deck Drainage | Professional Deck Builder from cdnassets.hw.net

Where the roof ties into the house, i removed the siding about 2 ft. Epdm is a rubber like sheet used for waterproofing surfaces. Up the wall and about 1 ft. This enabled me to fully adhere the roofing membrane about 2 ft. This article, building a roof deck was inspired after a client recently asked if i would replace her badly worn out roof deck. When installed professionally, a vinyl roof deck surface incorporates into the structure of your home, condo, or commercial development. Building a floating deck on an epdm rubber roof surface. I tore everything up, replaced the wood that needed it and built up the base and covered everything in epdm.

Here are the details in case you'd like to build your own building a deck with a roof version.

Roofs should be sloped about 1/4 every 12 to shed water. By paul (wa) i have an interesting problem. The cost will vary depending on the professionals hired, materials used, square footage, and weather conditions. Since most roof decks are floating structures that sit on top of flat roofs, it's crucial to weatherproof the roof below the deck to prevent water from seeping into the home. For clients to be able to clean out drains or scuppers at the low end of the roof, access to the roof membrane is crucial. Here are the details in case you'd like to build your own building a deck with a roof version. This enabled me to fully adhere the roofing membrane about 2 ft. It allows outdoor living space to be a place of leisure, not labor. Several commercial waterproof deck systems are available to create a dry space under a deck, but rune'stactic of adding a roof to a deck seems to be just as effective. Then, a frame is built on top, and pressure treated or composite decking is installed. Direct solid attachment of the roof membrane to this deck is not recommended; And it's inexpensive and easy to build using materials found at any home center. I pulled back the existing building paper after stripping the siding, installed the butyl

By incorporating the vinyl surface into the structure you're leaving much less room for water to find a way in. I pulled back the existing building paper after stripping the siding, installed the butyl The downspouts can be oriented to fit between joists spaced 12 or 16 inches on center. Building a roof deck over that surface, that would meet building codes, and not damage the roof, or cause premature failures and water leaks is not a simple matter of building directly on the existing roofing system. Then, a frame is built on top, and pressure treated or composite decking is installed.

Membrane Roofing NZ | Waterproof Deck & Flat Roof Dunedin from www.tituswaterproofing.co.nz

Since most roof decks are floating structures that sit on top of flat roofs, it's crucial to weatherproof the roof below the deck to prevent water from seeping into the home. Up the wall and about 1 ft. Once all seams are heat welded, slippers are installed between deck rafters and roof surface to protect the membrane. Cementitious coatings like desert crete are applied over metal lath stapled to the plywood sheathing. Roof expansion joints are designed to prevent membrane splitting and ridging (caused by either movement of the building, or movement of the roof assembly due to thermal expansion and contraction). Building a roof deck over that surface, that would meet building codes, and not damage the roof, or cause premature failures and water leaks is not a simple matter of building directly on the existing roofing system. I want to use sleepers that run same direction as the roof joists, correct? Just be sure to select a professionally installed product that has been tested to meet building code requirements for both a roofing membrane and pedestrian traffic coating.

Up the wall and about 1 ft.

Then, a frame is built on top, and pressure treated or composite decking is installed. Also, since roof decks are typically small (under 300 sq. The roof must be able to support 55 pounds per square foot at a minimum. I tore everything up, replaced the wood that needed it and built up the base and covered everything in epdm. Since most roof decks are floating structures that sit on top of flat roofs, it's crucial to weatherproof the roof below the deck to prevent water from seeping into the home. The gypsum sheathing is screwed to the metal deck. He selected tufdek, a vinyl roof deck membrane, which would provide a roof over the living space below, and a finished deck surface at the same time. I want to use sleepers that run same direction as the roof joists, correct? Roofing systems should be attached to this deck using a nailed base sheet. The coated ones rust and get stuck, while the stainless steel ones are too soft and snap or cam out. When i build a deck with more than 4 ft. Before installing a roof deck, you must be certain the roof is stable and weatherproofed. The contractor brought in to solve the problem, stanfield construction and repairs, quickly realized the door thresholds were set close to the deck height, leaving minimal roof for a new membrane.

This is often accomplished using epdm boots that fit over the openings. Roof expansion joints are designed to prevent membrane splitting and ridging (caused by either movement of the building, or movement of the roof assembly due to thermal expansion and contraction). Also, since roof decks are typically small (under 300 sq. Since most roof decks are floating structures that sit on top of flat roofs, it's crucial to weatherproof the roof below the deck to prevent water from seeping into the home. It's pitched ¼' per foot but without a spirit level you can't really tell.

EPDM Membrane for Warm Deck Roof Construction, Repair & Replacement from www.rubberroofingdirect.co.uk

Then, a frame is built on top, and pressure treated or composite decking is installed. A membrane roof should always provide positive drainage — the roof may look flat, but it shouldn't be level. When installed professionally, a vinyl roof deck surface incorporates into the structure of your home, condo, or commercial development. Up the wall and about 1 ft. Finally, a roof membrane is fully adhered to the coverboard. Building a roof deck over that surface, that would meet building codes, and not damage the roof, or cause premature failures and water leaks is not a simple matter of building directly on the existing roofing system. Then my deck frame joists attach to the sleepers, perpendicular to the joists? This coverboard is also screwed down to the metal deck.

It sounds like your building has a standard bitumen built up roof, as malor describes.

Where the roof ties into the house, i removed the siding about 2 ft. Finally, a roof membrane is fully adhered to the coverboard. Before installing a roof deck, you must be certain the roof is stable and weatherproofed. The downspouts can be oriented to fit between joists spaced 12 or 16 inches on center. This coverboard is also screwed down to the metal deck. By incorporating the vinyl surface into the structure you're leaving much less room for water to find a way in. But over the years, we've found that decking screws are challenging to remove: Duradek vinyl deck membranes are designed for strength, durability and slip resistance. Just be sure to select a professionally installed product that has been tested to meet building code requirements for both a roofing membrane and pedestrian traffic coating. When i build a deck with more than 4 ft. Roof expansion joints are designed to prevent membrane splitting and ridging (caused by either movement of the building, or movement of the roof assembly due to thermal expansion and contraction). It allows outdoor living space to be a place of leisure, not labor. When installed professionally, a vinyl roof deck surface incorporates into the structure of your home, condo, or commercial development.